Grout - Cementitious Class A
Product Description
Epirez Class A Superstrength Grout is a higher strength premixed cement based, non-ferrous, non-shrink grout, exhibiting good flow characteristics. This extra performance grout offers the advantage of low water requirements and high compressive strengths.
Class A Superstrength Grout should be specified for construction site applications demanding higher performance. Class A Superstrength Grout is supplied ready-to-use as a dry powdered product requiring only the addition of water to be used for a wide range of applications |
SikaGrout GP is a general purpose cementitious grout that is shrinkage compensated. SikaGrout GP is a blend of Portland cement, carefully selected & graded aggregate & admixtures.
It may be used for general purpose grouting, Machine and structural base plates, anchor bolts, Pre-cast concrete sections cavities, gaps and recesses. |
SikaGrout Ultra is a ready mixed, high quality cement grout that expands in two stages to counteract the shrinkage normally associated with Portland cement grouts. SikaGrout Ultra is a blend of Portland cement, carefully selected & graded aggregates & admixtures, enabling it to be self leveling & achieve very high strengths in short times making it suitable for critical grouting applications in the most demanding of circumstances.
It may be used for:
|
SikaGrout-UW is a ready to use, cementitious grout that can be used for applications underwater. The grout, when properly mixed, will have no significant ‘wash out’ of the cement phase. SikaGrout-UW is a blend of Portland cement, carefully selected and graded aggregates, and Sika admixtures, enabling it to achieve excellent flow, non wash-out characteristics, and high compressive strength.
SikaGrout-UW can be used for free flowing or pumped grout applications underwater, for reinstating concrete:
|
Dribond Non-Shrink Grout is a pre-mixed, non-shrink Class “A” cement grout. It is an expanding non-ferrous grout, consisting of a dry-premixed blend of Portland Cement and graded,siliceous aggregate with set regulating and reactive chemical agents. Note: Contains no calcium chloride.
Dribond Non Shrink Grout may be used for:
|
Flowfill Grout GP is a multi purpose non-shrink, Class A cementitious grout complying with the SAA MP20 part 3. Flowfill Grout GP is based on Portland cement, graded aggregate & chemical additives, which impart controlled expansion whilst in the plastic state. The gaseous expansion system compensates for shrinkage & settlement in the plastic state.
It may be used for:
|
Bostik Flowfill Grout UW is based on Portland cement, graded aggregate and chemical additives, which impart controlled expansion whilst in the plastic state. Flowfill Grout UW is used for free flow or pumped grouting applications underwater or in tidal zones. There is no significant “wash-out” of the cement paste and in fact displaces water when used in submerged conditions.
It may be used for:
It may be used for:
- Bridge columns.
- Quarry pillars.
- Concrete piling.
- Slipways.
- Dams.
- Wharf columns.
Bostik Flowfill Panel Grout is based on Portland cement, graded aggregate and chemical additives, which impart controlled expansion whilst in the plastic state. The gaseous expansion system compensates for shrinkage and settlement in the plastic state.
BASF Economical Construction Grout is a ready-to-use natural aggregate, general purpose grout which undergoes controlled expansion in the plastic state. Economical Construction Grout may be placed in dry (damp) packed, plastic or fluid consistency and is generally used in applications requiring a grout thickness between 25mm and 100mm.
It may be used for all general purpose grouting operations including:
It may be used for all general purpose grouting operations including:
- non-critical column and equipment bases
- an in-fill grout for cavity block walls
- in caulking of joints and pipes
- between and under pre-cast panels and other joints where total load-bearing is not required
Basf Masterflow 95 is a ready-to-use pumpable, natural aggregate, general purpose grout which undergoes controlled expansion in the plastic state. Masterflow 95 is a gas generating, shrinkage compensating grout as defined by AS 1478.1-2000, Appendix E, section E5.1 (formerly known as Class A). Masterflow 95 may be placed in dry (damp) packed, plastic or fluid consistency and is generally used in applications requiring a grout thickness between 12mm and 100mm.
Masterflow 95 is recommended for:
Masterflow 95 is recommended for:
- All general purpose grouting operations with clearances of 12mm to 100mm including:
- non-critical column and equipment bases
- an in-fill grout for cavity block walls
- in caulking of joints and pipes
- between and under pre-cast panels and other joints where total load bearing is not required.
- underpinning where a grout similar in appearance to concrete is required.
Parchem Construction Grout is a general purpose shrinkage compensated cementitious grout. It is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a flowing shrinkage compensated grout for gap thicknesses up to 100 mm.
Construction Grout is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded filler is designed to assist uniform mixing and produce a consistent grout. Maximum aggregate size for pumping is 0.3 mm.
It is used for general purpose grouting when completely filling concrete voids or grouting between a base plate and a substrate e.g. the grouting of a stanchion base plate.
Construction Grout is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded filler is designed to assist uniform mixing and produce a consistent grout. Maximum aggregate size for pumping is 0.3 mm.
It is used for general purpose grouting when completely filling concrete voids or grouting between a base plate and a substrate e.g. the grouting of a stanchion base plate.
Parchem Conbextra GP is a general purpose shrinkage compensated cementitious grout, is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a flowing shrinkage compensated grout for gap
thicknesses from 10 mm up to 100 mm.
Conbextra GP is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded filler is designed to assist uniform mixing and produce a consistent grout. Maximum aggregate size for pumping is 1.2 mm.
It is used for general purpose grouting where it is essential to eliminate shrinkage when completely filling voids or grouting between a base plate and substrate, e.g. the grouting of a stanchion base plate. It can also be used for anchoring a wide range of fixings such as masts and anchor bolts.
thicknesses from 10 mm up to 100 mm.
Conbextra GP is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded filler is designed to assist uniform mixing and produce a consistent grout. Maximum aggregate size for pumping is 1.2 mm.
It is used for general purpose grouting where it is essential to eliminate shrinkage when completely filling voids or grouting between a base plate and substrate, e.g. the grouting of a stanchion base plate. It can also be used for anchoring a wide range of fixings such as masts and anchor bolts.